Skip to the reports
Aquifer to TapSan Antonio house water, filed in short reports
Beats

Your pipesP-03

Find a leak with your meter

Filed Nov. 11, 2026 · checked against 5 sources · Aquifer to Tap

To find a leak with a SAWS meter, shut off every water use and read the flow-rate screen: SAWS says any number other than zero means a leak on the property.

0gallons per minute a leak-free house should show with all water offSource: SAWS

An open meter box in the lawn by the curb with a smart water meter and its small digital display inside
Open plastic meter box in St. Augustine grass by a curb, holding a residential smart water meter with a digital display and radio unit. AI-generated picture.

SAWS's leak page gives two meter tests for its ConnectH2O electronic meters, and the TCEQ adds a third for toilets. All three cost nothing. Because everything from the meter toward the house is the owner's to repair, a positive result is the owner's job to chase; see who owns which pipe.

Where is the meter, and which screen?

Most SAWS meters sit underground under a round or oval lid, usually in a straight line between the front hose bib and the street. Corner lots may have the meter at the side, and some parts of the city use the alley. SAWS warns to watch for spiders and ants when lifting the lid.

The electronic display has seven screens, stepped through by tapping an optical button: errors and alerts, current total volume, flow rate in gallons per minute, water temperature, software version, a high-resolution reading and a display test. The SAWS video on this page dates from 2018 and shows an older mechanical meter with a spinning flow indicator. On a ConnectH2O meter the flow-rate screen does that job. More on the screens is in reading your ConnectH2O meter.

The three tests

Flow-rate check. Turn off every tap and water-using appliance, inside and out, and switch off the irrigation controller. Read the flow-rate screen. Zero means no water is moving; any other number means a leak somewhere past the meter.

One-hour check. Write down the current total volume. Use no water for an hour, then read it again. A higher number means water left the pipes while nothing was on. This catches slow leaks that a quick look can miss.

Toilet dye check. The TCEQ's owner advice says to put water-based dye in the toilet tank and watch the bowl for 10 minutes without flushing. Color in the bowl means the tank is leaking into it.

What each check finds, per SAWS and TCEQ (checked Nov. 11, 2026)
CheckTimeWhat a leak looks like
Flow-rate screenA minuteAny reading other than zero
Total-volume readingOne hourTotal higher at the end
Dye in toilet tank10 minutesColor reaches the bowl

If the meter shows flow but every toilet passes, SAWS lists places to look: stains, mildew or moisture on ceilings, walls and floors; the area around the slab; green or soggy patches in the yard; and standing water near the water heater. It also says to make sure a water softener is working properly. A leak under the foundation is covered in slab leaks on clay soil.

Why the reading matters for the bill

SAWS bills in full 100-gallon units, so a meter reading of 2,814.4 gallons bills as 2,800, according to its meter-reading guide. A steady leak adds units every month. Timing matters too: SAWS sets the sewer charge from use between mid-November and mid-March, and an unrepaired leak can lift that winter average for the year ahead.

ConnectH2O meters also send hourly readings that feed leak and high-use alerts in My Account, according to SAWS's ConnectH2O page. Once a leak is fixed, SAWS may credit part of the lost water; see leak adjustments.

Watch How To Detect Water Leaks — from the San Antonio Water System channel, 1:09. A SAWS staffer shows how to shut off every water use inside and out, find the meter (front yard, side yard on corner lots, or the alley), and watch the flow indicator to see whether water is still moving.

Key facts

  • SAWS: with all water off, any flow-rate reading above zero means a leak.
  • One-hour test: record total volume, use no water for an hour, compare.
  • TCEQ toilet test: water-based dye in the tank, 10 minutes, no flushing.
  • SAWS bills in full 100-gallon units.
  • Winter use from mid-November to mid-March sets the sewer charge.

Sources

  1. SAWS — Reading Electronic Water Meter to Help Identify Leaks (checked Nov. 11, 2026)
  2. SAWS — How To Read Your Electronic Water Meter (checked Nov. 11, 2026)
  3. SAWS — ConnectH2O hourly readings (checked Nov. 11, 2026)
  4. TCEQ — Advice for an owner of an on-site sewage facility (checked Nov. 11, 2026)
  5. SAWS — Winter Averaging (checked Nov. 11, 2026)